This is a Hard to find part. Fits Valve Rockers for the 800 - 1000 V-Twin.
This Air Filter is 6 1/2" Tall and has a 5" O.D. Comes with a Secondary Inner Filter as shown.
This is for the ODES Disc Mounting Shoulder Bolts sold as a pack of (4) Bolts for 1 Disc.
Commonly Used on Banjo Bolts
Add this to both Front and Rear Diff Vent Hoses, no clamps required.
Factory HiSun FLYWHEEL (Magneto) PULLER 38mm
FITS MOST ATV - UTV 800 and 1000 'V-Twin' MODELS 2008-2024
We Now List Many HiSun Special Tools !
* Now Fits most 2019 and Newer HiSun 550, 700 and 750 *
This PULLER is needed to Replace or Remove the Flywheel
ODES & HiSUN 800 and 1000 ATVs and UTV'S INCLUDING,
MASSIMO, BENNCHE, HISUN, Dominator (and many more)
This Gas Cap should fit many newer Models from Applestone that is Distributed by Massimo for the UTV WarriorFits many Female Neck with an I.D. (inside hole size) of 40mm , just over 1.5". The O.D of the cap is 44mm.
This fits HiSun and Odes Injectors. This is cut from a brand new wire harness. Just Splice/Solder/Shrink Wrap !
Fits Front and Rear HiSun Axles 450-1000.
Fits Odes Rear Axles (Odes Front are 22mm)
The Inside Diameter is approx. 22.5
This set of O'Rings is specially to fit the Injectors from all HiSun and Odes Models !
We also have the Clutch cover 3 piece Bolt with Washer and Rubber Seal if needed. 21040302201
We also have the Clutch cover 3 piece Bolt with Washer and Rubber Seal if needed. 21040302201
3-Bolt Hole Front Diff Actuator, also know as Divide Device, Servo, Transfer Case or 2-WD/4-WD Motor.
We also have the Clutch cover 3 piece Bolt with Washer and Rubber Seal if needed. 21040302201
Rear Wheel Hub
Also known as Mounting Seat Rear Hub
2011-2013ish had 26mm Splines for the Axles and Hubs.
Now updated to 28mm Splines, 26mm are discontinued and N/A.
Complete with (4) 10mm x 1.5 Wheel Studs as Shown
Fits ODES 800 UTV Early Model Dominator
2011 - 2023ish
Stud Pattern #1 to #3 = 110mm (Known as 4x110)
Disc Bolt Pattern #1 to #3 = 100mm
ODES Speed Controller 2-plug Connector with 1-Wire
ODES 800 UTV X-2 & X-4
This is for 10109360000A
others below;
*Only 1 Plug Limiter Box = 10909360001*
**2-Plug Limiter with 2-wire = 10109360001**
Steering Knuckle Right
Front/Passenger (Short 4" Arm)
Complete with 2 Bearings and 2 Seals as Shown
3 Different Knuckles Available for the Front !
Please Study the Arm Length and Type of Bearing Inside.
Fits ODES UTVs with Short Travel (Round A-Arms)
Rear Left Brake Caliper with Parking Activators and Pads !
For the Odes UTV 800 & 1000
FITS THE FOLLOWING MODELS:
Fits D2, D4, X2, X4, Raider, Ravager UTV 800 & 1000 and Many More !
2016ish - 2024
Rear Right Brake Caliper with Parking Activators and Pads !
For the Odes UTV 800 & 1000
FITS THE FOLLOWING MODELS:
Fits D2, D4, X2, X4, Raider, Ravager UTV 800 & 1000 and Many More
2016 ish - 2024
These Front Brake Pads are for the Late Model RED Calipers (see all pictures) Left and Right are the same.
These are Rear Pads for many different Manufactures for the Single Piston Calipers. Appelstone, Massimo and more.
This CVT Belt is the Odes Factory Belt from CV Tech. Fits FX3 Models, HVAC 1000cc and all models that have the Rear Diff and Transmission build together in the same cases. Measures 43.25" O.D. and 1.3" (32.4mm) Wide.
This fits most Odes Dominators that is approx. 28" Long. The U-Joints are Not replicable.
This has Approx. Compressed Length of 12.5" with slide movement of over 1".
Please study the Chart to select proper length.
This has Approx. Compressed Length of 14.5" with slide movement of over 1".
The next size smaller is approx. 13" compressed or longer is 16" compressed.
Please study the Chart to select proper length.
-
This has Approx. Compressed Length of 16" with slide movement of over 1".
The next size smaller is approx. 14.5" compressed or longer is 44" compressed.
Please study the Chart to select proper length.
- Out of stock
Fits 2011 - 2014ish ODES Dominator 800 UTV
(maybe newer 'ST' Travel Models)
(Complete with all Bolts, Mounts and Wiring)
This Fits Original 'D' Frame
- Out of stock
The 0ld Flywheel of 4.1" and 4.5" Black Plug Flywheel is not in production and not available.
This Grey Plug Rotor for the Gray Plug Flywheel is all that is available.
